Technical Data

TOPZOL TSE DYES - High one-time success dye

Show Details


Excellent light fastness - min. grade 4 per ISO105- B02.
Excellent perspiration light fastness - min. grade 4 per ISO 105-B07.
Excellent compatibility and reproducibility.
High one-time success rate.
Good solubility and high stability of dye liquor especially suitable for dyeing at low liquor ratio.

Available colors:
Tri-colors for light shade
Yellow TSE
Light Red TSE
Light Blue TSE
Tri-colors for medium to heavy shade
Gold TSE
Cardinal TSE
Navy TSE
Brilliant Yellow TSE
Brilliant Orange TSE
Brilliant Scarlet TSE
Brilliant Red TSE
Deep Blue TSE
Brilliant Blue TSE
Turquoise TSE
Brilliant Green TSE
Black TSE

Exhaustion dyeing process
40 deg.C
Adding Dye
10 minutes
Adding auxiliary
Raising temperature to 60 deg.C (1.5 deg.C per minute)
Dyeing at 60 deg.C for 10 – 15 minutes
Adding Alkali
Dyeing at 60 deg.C for 30 – 50 minutes
Wash off

Salt and Alkali amount (unmercerized):
O.W.F.% <0.5%
Salt (g/l) 5-20
Soda Ash (g/l) 5-10
O.W.F.% 0.5-1.0
Salt (g/l) 20-30
Soda Ash (g/l) 8-15
O.W.F.% 1.0-3.0
Salt (g/l) 30-60
Soda Ash (g/l) 15-20
O.W.F.% 3.0-5.0
Salt (g/l) 60-70
Soda Ash (g/l) 20
O.W.F.% >5.0
Salt (g/l) >70
Soda Ash (g/l) 20

Salt and Alkali amount (mercerized):
O.W.F.% <0.5%
Salt (g/l) 5-15
Soda Ash (g/l) 5-8
O.W.F.% 0.5-1.0
Salt (g/l) 15-25
Soda Ash (g/l) 8-10
O.W.F.% 1.0-3.0
Salt (g/l) 25-50
Soda Ash (g/l) 10-15
O.W.F.% 3.0-5.0
Salt (g/l) 50-60
Soda Ash (g/l) 15-20
O.W.F.% >5.0
Salt (g/l) >60
Soda Ash (g/l) 20

Wash-off procedure:
Wash for 10 min. at 50 deg.C
Neutralize at 50 deg.C for 10 min.
Soap at 90 deg.C for 10 - 20 min. with 1-2 g/L soaping agent.
Wash for 10 min. at 50 deg.C
Cold wash for 10 min.

Dyeing Procedure of Reactive NA type - High Perspiration Light Fastness Reactive Dye

Reactive NA
Reactive NA type
(High Perspiration Light Fastness)

Special Properties:
Excellent light fastness and perspiration light fastness especially for pale shade.
Good washing-off property.
Good compatibility and reproducibility.
Good build-up.
No need to add "Alkali" during dyeing process.

Dyeing Process:
Start from 25 to 30 degree C
Add NA Dye, Salt, Stabilizer MTB
Run for 20 minutes
Raise temperature from 30 degree C to 85 degree C, 1 degree C per minute.
Dyeing at 85 degree C for 30 minutes
Washing – Soaping – Washing

Soaping Process:
Washing at 50-55 degree C X 10 min.
Soaping at 95 degree C X 15 min.
Cold rinse
Cold rinse

Dosage of Salt and Stabilizer MTB
Dyeing depth (o.w.f.)
Below 0.25% o.w.f., salt 10g/l to 20g/l, Stabilizer MTB 1g/l
From 0.25% to 0.5% o.w.f., salt 20g/l to 30g/l, Stabilizer MTB 1g/l
From 0.5% to 1.0% o.w.f., salt 30g/l to 50g/l, Stabilizer MTB 1g/l to 1.2g/l
Above 1% o.w.f., salt above 50g/l, Stabilizer MTB 1.2g/l

Reactive NA dyes are sensitive to peroxide even only 5 ppm residue, recommend using our peroxide killer to remove peroxide residue.

Dyeing procedure of Topcion HEXL dye / Reactive HEXL dye

HEXL dye
Dyeing procedure of Topcion HEXL dye / Reactive HEXL dye:

TOPCION HEXL is particularly suitable for exhaust dyeing. Levelling effect is excellent.
The washing fastness of TOPCION HEXL is better than HE Type dye.
TOPCION HEXL can be easily washed off for unfixed molecule dyes.
TOPCION HEXL dye is good for using in combinations with each other.

Dyeing method
Exhaustion dyeing / Winches, jet-dyeing machine, circulation equipment
Liquor ratios 1:6 to 1:20
Start from room temperature
Run 10 minutes
Add HEXL dye
Run 20 minutes
Add salt 1/10
Raise temperature to 80 degree C, 1~2 degree C per minute
Add salt 3/10 at 45 to 50 degree C.
Add salt 6/10 at 60 to 65 degree C
Dyeing at 80 degree C for 15 minutes
Add soda ash 1/2
Run 15 minutes
Add soda ash 1/2
Keep dyeing for 30 to 70 minutes
Soaping – Washing

Recommended Dosage of Salt and Soda ash (alkali)
Dyeing depth below 0.5% o.w.f., salt 0 to 20 g/l, soda ash 15 g/l
Dyeing depth 0.5% to 1% o.w.f., salt 20 to 40 g/l, soda ash 15 g/l
Dyeing depth 1% to 2% o.w.f., salt 40 to 60 g/l, soda ash 20 g/l
Dyeing depth 2% to 4% o.w.f., salt 60 g/l, soda ash 20 g/l
Dyeing depth above 4% o.w.f., salt 80 g/l, soda ash 20 g/l

Soaping After Exhaust Dyeing
Rinse by hot water for 10 to 20 minutes
Soaping at the boil for 15 to 30 minutes
Rinse by warm water for 10 minutes



Product Name:
Acrylic Polymer in Primary form (Binder-WB-568E)
CAS NO.: 25767-39-9
Heavy Metals: NONE
Boiling Point: 100°C
Viscosity: NONE
pH Value: 5-7
Usage: Textile Printing
Ingredient; Acrylic resin 85-95%
Thickener 5-15%
Appearance: Binder
Flashing Point: 180°C
Dissolvability: NONE
Storage Life: 12 Month

Acrylic Polymer in Primary form (Binder-WB-568E) - Materials Safety Data Sheet

Materials Safety Data Sheet

1 Supplier Name / Address:
Taiwan Dyestuffs & Pigments Corp.
Tel. 886-3-3582296 Fax. 886-3-3582294

Trade Name: Acrylic Polymer in Primary form (Binder-WB-568E)
Product Name: Acrylic Polymer in Primary form (Binder-WB-568E)

2 Composition Information
Water base acrylic resin 25767-39-9 85-95%
Thickener N/A 5-15%

Composition of Endanger Material (%):0 %

3 Possible Hazards / Hazards Identification:
No hazardous product as specified in Directive 67/548/EEC

4 First Aid Measures
General Advice:
Do not swallow. Properly use with instruction will minimize risks.
Remove patient from explosure. Obtain medical attention if ill effects occur.
Skin Contact:
Any skin contact must be washed with water.
Contact With Eyes:
Any eye contact must immediately irrigate with water for at least 10 minutes. Obtain medical attention.
Wash out mouth with water. Obtain medical attention if ill effects occur. Further medical treatment-symptomatic treatment and supportive therapy as indicated.

5 Fire Fighting Measures
Special Exposure Hazards:
This material may form flammable dust clouds in air. Toxic fumes of NOx may be.
Special Protective Equipment for Fire Fighters:
Extinguishing Media: Water Spray / Foam / Dry Chemical / CO2
Special fire fighting procedures: None
Unusual Fire & Explosion Hazards: None

6 Accidental Release Measures
A. Personal Precautions:
Ensure suitable personal protection during removal of spillage.
B. Environment Precautions:
Ensure any spillage does not enter drains, contain and collect up.
C. Collection and Disposal Considerations:
Collect up spillage and transfer to sealable containers for disposal.

7 Handling and Storage:
Avoid contact with skin and eyes. Keep away from moisture. Keep containers tightly closed. Store away from excessive heat and sources of ignition.
This material is supplied in powder form and when handled will give rise to dust.
Consideration should be given to the installation of local exhaust ventilation.

8 Exposure Control and Personal Protection:
A. Respiratory Protection
Wear disposable respiratory protective equipment to standard EN 149 FFP 2
B. Hand Protection
P.V.C. or rubber gloves.
C. Eye Protection
Close fit goggles.
D. Skin Protection
Industrial overalls.

9 Physical And Chemical Properties:
Boiling Point: 100°C
Density (30°C): 1.1-1.20
Melting Point: 100°C
Autoignition Temperature: N.A
Burn Point: 180°C
Solubility in water: Soluble
Appearance and odor: Binder, Odorless
Packing: Plastic drum

10 Stability and Reactivity:
Stability-stable in ambient conditions.
Condition to avoid - avoid working in confined spaces with poor ventilation.

11 Toxicological Information:
Oral Rat LD50 > 2000 mg/kg after consideration of similar products.
Inhalation- slightly irritant nuisance dust.
Long term effects - no significant long term effects reported.

12 Ecological Information:
No data available.

13 Disposal Considerations:
Disposal should be in accordance with local, state or national legislation.

14 Transportation Information:
Not classified as a dangerous for transport.
DOT (49 CFR 172)
Domestic Ground Transport
Proper Shipping Name: Unrestricted
Hazard Class or Division: Unrestricted.
Identification Number: None
Marine Pollutant: None
Proper Shipping Name: Unrestricted
Hazard Class or Division: Unrestricted.
UN or ID Number: None
Proper shipping name : Unrestricted.
Hazard Class or Division: Unrestricted.
UN or ID Number: None
Packing group : None

15 Regulatory Information:
Not classified as dangerous for supply or use.

16 Other Information:
The information contained herein is based on the present state of our knowledge and does not therefore guarantee certain properties. Recipients of our product must take responsibility for observing existing laws and regulation.